Initialising ...
Initialising ...
Initialising ...
Initialising ...
Initialising ...
Initialising ...
Initialising ...
beam extracted from an RF-driven high-intensity H ion sourceShinto, Katsuhiro; Shibata, Takanori*; Wada, Motoi*
Proceedings of 18th Annual Meeting of Particle Accelerator Society of Japan (Internet), p.230 - 233, 2021/10
In most proton accelerator facilities such as J-PARC, SNS, CERN, a H ion source equipped with a 2-MHz rf driver for plasma generation produces H beams. We have reported H beam characteristics extracted from the J-PARC rf-driven high-intensity H ion source. We have been developing an emittance measurement apparatus equipped with a highly time-resolved data acquisition system in order to observe fluctuation of the beam emittance in association with the frequency of the rf driver. By using this apparatus, we found that the beam emittance is fluctuated with the frequency with the rf driver and higher harmonics. We will show some obtained results of the emittance fluctuation.
Shibata, Takanori*; Shinto, Katsuhiro; Wada, Motoi*; Oguri, Hidetomo; Ikegami, Kiyoshi*; Okoshi, Kiyonori; Nammo, Kesao*
AIP Conference Proceedings 2373, p.050002_1 - 050002_9, 2021/08
Oscillation of emittance and Twiss parameters in the negative ion beam from the J-PARC 2-MHz RF ion source is measured by applications of a double-slit emittance monitor located at the RFQ (Radio Frequency Quadrupole) entrance. The emittance monitor is equipped with a newly-developed 60 MS/s data acquisition system, so that beam current oscillation in a few MHz can be observed with enough time resolution. From the measurement, it is shown that the beam phase space consists of (1) a DC component in the beam core, (2) a 2-MHz oscillating component which takes place both in the beam core and the halo and (3) a doubled RF frequency (4 MHz) oscillation which slightly exists in the beam halo. The major component is the 2-MHz component, which resultantly decides the beam emittance oscillation frequency. A typical value of the beam emittance in the present experiment is 0.34 
mm-mrad, while the amplitude of the 2 MHz oscillation is around 0.04 mm-mrad. The results indicate that the high-frequency oscillation component occupying about ten-percent of the beam from the RF source travels a few meters passing through a magnetic lens focusing system.
beam with orifice in J-PARC front-endShibata, Takanori*; Ikegami, Kiyoshi*; Nammo, Kesao*; Liu, Y.*; Otani, Masashi*; Naito, Fujio*; Shinto, Katsuhiro; Okoshi, Kiyonori; Okabe, Kota; Kondo, Yasuhiro; et al.
JPS Conference Proceedings (Internet), 33, p.011010_1 - 011010_6, 2021/03
Together with the intensity upgrade in J-PARC Linac Front-End, improvement of RFQ transmission ratio is an important task. This RFQ transmission ratio depends strongly upon the solenoid current settings in the low energy beam transport line (LEBT). In the present study, high beam current cases (72 mA and 88 mA H beam current in LEBT) are investigated at a test-stand. Phase space distributions of the H beam particles at the RFQ entrance are measured and compared with numerical results by Particle-In-Cell simulation. As a result, it has been clarified that a 15 mm 
orifice for differential pumping of H
gas coming from the ion source plays a role as a collimator in these beam conditions. This leads to change the beam emittance and Twiss parameters at the RFQ entrance. Especially in the condition with the beam current up to 88 mA in LEBT, the beam collimation contributes to optimize the phase space distribution to the RFQ acceptance with relatively low solenoid current settings. As a higher solenoid current setting would be necessary to suppress the beam expansion due to high space charge effect, these results suggest that current-saving of the solenoids can be possible even in the higher beam intensity operations.
Shinto, Katsuhiro; Okoshi, Kiyonori; Shibata, Takanori*; Nammo, Kesao*; Ikegami, Kiyoshi*; Takagi, Akira*; Namekawa, Yuya*; Ueno, Akira; Oguri, Hidetomo
AIP Conference Proceedings 2052, p.050002_1 - 050002_7, 2018/12
Times Cited Count：6 Percentile：93.93(Physics, Applied)In the 2017/2018 campaign, the J-PARC cesiated rf-driven negative hydrogen (H) ion source producing H beam with the beam current of 47 mA accomplished three long-term operations more than 2,000 hours without any serious issues. On the final day of this campaign, the ion source produced an H beam current of 72 mA so that the linac commissioning group could demonstrate the beam current of 60 mA at the linac exit. We are also conducting an endurance test of a J-PARC-made antenna at a test bench. The antenna achieved the operation time approximately 1,400 hours.
ion sourceShinto, Katsuhiro; Shibata, Takanori*; Miura, Akihiko; Miyao, Tomoaki*; Wada, Motoi*
AIP Conference Proceedings 2011, p.080016_1 - 080016_3, 2018/09
Times Cited Count：5 Percentile：91.75(Physics, Applied)Miura, Akihiko; Moriya, Katsuhiro; Miyao, Tomoaki*
Proceedings of 9th International Particle Accelerator Conference (IPAC '18) (Internet), p.5022 - 5025, 2018/06
A wire-scanner monitor using metallic wire is reliably employed for the beam-profile measurement in the J-PARC linac. Because the loading of negative hydrogen (H
) ion beam on a wire increases under high-current beam operation, we focus on using a high-durability beam profile monitors by attaching another wire material. Carbon nanotubes (CNT) are made of graphite in a cylindrical shape and have a tensile strength not less than 100 times that of steel. The electric conductivity has higher than that of metals, and hardness is endured thermally around 3000
C in a vacuum circumstance. We applied the wires made from CNT to WSM and measured transverse profiles with a 3-MeV H beam. As a result, we obtained the equivalent signal levels taken by carbon wire made of polyacrylonitrile without any damage. In this paper, the signal response when the CNT is irradiated with an H beam and the result of beam profile measurement. In addition, the surface of CNT after 3-MeV beam operation was observed.
ion source upon the extracted beamShinto, Katsuhiro; Shibata, Takanori*; Wada, Motoi*
Proceedings of 14th Annual Meeting of Particle Accelerator Society of Japan (Internet), p.648 - 650, 2017/12
In J-PARC, peak H current of several tens mA is extracted from an ion source driven by a solid-state rf amplifier with the frequency of 2 MHz for production of a cesiated hydrogen plasma. In case of the rf-driven ion source for producing the high-intensity H current, the plasma density in the source chamber is so high that the ion sheath around the beam extraction area can follow the rf oscillation. The H beam current fluctuation as large as approximately 1 mA was observed at the average beam current of 44 mA measured by a Faraday cup installed downstream of the ion source. The beam exhibited some fluctuation to the transverse motion as well. To further clarify this high frequency oscillation of the beam extraction sheath, we propose a measurement system using a time-resolved and highly sensitive emittance monitor in order to observe the real-time beam fluctuation in the phase space.
Miura, Akihiko; Okabe, Kota; Yoshimoto, Masahiro; Yamane, Isao*
Proceedings of 5th International Beam Instrumentation Conference (IBIC 2016) (Internet), p.856 - 859, 2017/03
no abstracts in English
Miura, Akihiko; Yoshimoto, Masahiro; Okabe, Kota; Yamane, Isao*
Proceedings of 13th Annual Meeting of Particle Accelerator Society of Japan (Internet), p.1102 - 1106, 2016/11
no abstracts in English
ion sourceShibata, Takanori*; Takagi, Akira*; Shinto, Katsuhiro; Ikegami, Kiyoshi*; Okoshi, Kiyonori; Nammo, Kesao*; Oguri, Hidetomo; Naito, Fujio*
no journal, ,
For the application of bias voltage in J-PARC Radio Frequency (RF) negative ion source, characteristics of the voltage variation on the plasma electrode are investigated with different RF plasma conditions. A continuous 30 MHz RF power up to 10 - 100 W and a pulsed 2 MHz RF power up to 5 - 20 kW are injected from internal RF antenna coil. In each case, time structure of the voltage between the plasma electrode and the isolated source chamber is measured by voltage probe with different measurement resistances. Behavior of the measured voltage differs strongly whether the RF plasma is in the E mode phase by 30 MHz RF injection or in the H mode phase by 2 MHz RF injection. The results suggest that formation of capacitively coupled electric field and inductively coupled magnetic field decide the positive and the negative fluxes coming into the chamber wall. Under the same plasma condition as in the J-PARC user operation, peak value of the voltage between the source chamber and the plasma electrode is around 60 - 80 V and frequency of the voltage is a combination of 2 MHz and 30 MHz. For the continuous bias voltage application on the plasma electrode, additional distributed constant circuit to cancel these voltage oscillation and high voltage bias power supply are required.
